Cars & Trucks - Page 3 - Recent Questions, Troubleshooting & Support

Good place to get a vacuum gauge hooked up and identify problems using that tool. Without the gauge, check your exhaust and see how much if passing through the converter. You can do this by testing the temperature of the exhaust before and after the converter making sure the converter/exhaust isn't restricted. As the vehicle warms up a bad converter can cause the symptoms you are describing.

Question edited for clarity. Question moved to model category. No, it is no a replaceable item and is located in the bottom of the fuel tank and is part of the fuel pump Attached to the fuel pump in the gas tank. It's not a replaceable part. You would have to replace the pump in the tank. Actually it is replaceable, but not a maintenance item. Apr 12, 2011

fuel filter location on 01 CL ? - Acura Enthusiast Community

AcuraZine https://acurazine.com > ... > 2G CL Problems & Fixes ..

Your light switch controls those items, it may be defective.

Only way to get the code is dealership or someone with a radio programmer aka auto scanner

Question edited for clarity and spelling. Question moved to model Category. Help in the link https://www.google.com/search?q=2001+Mitsubishi+Montero.+Diagram+of+fuel+pump+relay ..

Question edited for clarity and spelling. Question moved to model category. Ideas in the link, but the easy way is to use the spare key. All cars come with 3 sets. Or an Auto Locksmith. https://www.google.com/search?q=buick+lacrosse+keys+locked+in+car ..

Question edited for clarity and correct model name. Question moved for model category. Diagram here. It should be in the Owner Manual as well. https://www.google.com/search?q=1993+ford+explorer+sport+trac+jacking+points+diagram ..

Question edited for clarity and spelling. https://www.google.com/search?q=bmw+e36+convertible+roof+not+working ..

Question editerd for clarity.

Question moved to model category, however, there are 3 engine sizes for that model.

VEHICLE 2008 Jeep Commander All

Parts

Accessories

3.7L Gas; Engine 4.7L Gas; Engine 5.7L Gas; Engine That part from AUTOZONE!! 2008 Jeep Commander Vehicle/Transmission Speed Sensor AutoZone https://www.autozone.com/engine-management/vehicle-transmission-speed-sensor/jeep/commander/2008 .

P0717 OBD-II Trouble Code: Input/Turbine Speed Sensor ...

YourMechanic https://www.yourmechanic.com > Articles P0717 is a diagnostic trouble code (DTC) for "Input/Turbine Speed Sensor No Signal". This can happen for multiple reasons and a mechanic needs to diagnose ... Missing: Commander ‎' Show results with: Commander

Code P0717 Jeep Input Speed Sensor 1 Circuit No Signal

AutoCodes https://www.autocodes.com > p0717_jeep Repair Information for P0717 Jeep code. Learn what Input Speed Sensor 1 Circuit No Signal means, location and how to repair? Similar to this https://jeepspecs.com/wj-generation/wj-jeep-parts-equipment/transmission-input-output-speed-sensors/ ..

Question edited for a lot more clarity.

Hino J08 engine specs, bolt torques

Barrington Diesel Club https://barringtondieselclub.co.za > hino > hino-j08 Hino J08E, J08C specs and bolt torques with links to manuals ... Hino J08E Connecting Rod Bolts Step1 = 51 lb.ft ... main bearing cap bolts, connecting rod cap ...

Workshop Manual Hino J08C No.1 ' PDF

Scribd https://www.scribd.com > document > WORKSHOP-MA... ... SPECIFICATIONS DIESEL ENGINE FOR INDUSTRIAL USE HINO) §=JO8C-T eannzn. ... bearing cap bolt are tightened to the specified torque. ... Connecting rod bearing 16. "); background-repeat: repeat-x; display: inline-block; overflow: hidden; position: relative; background-size: 14px 11.4px; height: 11.4px; width: 68px;"> "); background-repeat: repeat-x; display: block; background-size: 14px 11.4px; height: 11.4px; width: calc(62px);"> Rating: 4.6 · ‎ 10 votes

Hino J08C Engine Torque Specs

JustAnswer https://www.justanswer.com > Truck Repair Sep 29, 2012 - Hi I'm Wayne I will help you with this. Good Morning Rod Bearings 51 FT/LBS + 90° + 45° Main Bearings 196-209 FT/LBS Head Bolts Missing: connecting ‎' Show results with: connecting

HINO DIESEL ENGINE WORKSHOP MANUAL

jimcontent.com https://s4b621f162e87bd31.jimcontent.com > name PDF Cylinder head bolt, crankshaft main bearing cap bolt, connecting rod bearing cap bolt, etc. ! CAUTION. • Measure the overall length of the bolt before. ..

Per Chilton Auto repair manual:

Removal & Installation

1. Raise and safely support the vehicle.
   
2. Remove the rear wheel.
   
3. Siphon a small amount of brake fluid from the master cylinder reservoir.
   
4. Insert a small prybar through the caliper opening and pry the caliper cover (using the outboard brake pad) to bottom the piston in the caliper bore.
   
5. Remove the caliper slide bolts.
   
6. Remove the caliper from the anchor.
   
   WARNING Support the brake caliper with mechanics wire. Do not let the caliper hang by the brake hose.
   
7. Remove the brake pads from the caliper.
   

To install:

1. Install the brake pads onto the caliper.
   
2. Lubricate the slide pin bolts with grease provided with the brake pads, or suitable silicon grease equivalent.
   
3. Install the caliper on the anchor and tighten the slide pin bolts to 18 ft. lbs. (25 Nm).
   
4. Install the rear wheel.
   
5. Lower the vehicle.
   
6. Pump the brake pedal several times until a firm pedal is obtained in order to properly seat the pads.
   
7. Refill the brake fluid reservoir to the proper level.
   

Thomas; Under hood, next to the air filter housing, behind the battery, in front of the strut tower. Refer to the Owner's Manual for description of fuses within the box. page 373 in manual. link below is your manual, press the helpful button http://www.jeep.com/download/pdf/manuals/2008-Patriot-1st.pdf

I would take this one. Do you have the Evacuation Pump to suck out the air and moisture first? http://flash52.ru/images/frion/norma.pdf https://www.google.com/search?q=2010+toyota+corolla+le+refrigerant+capacity ..

On the top of the bellhousing. From the drivers point of view it is in the 11:00 o'clock position. The harness wraps around the back of the bellhousing and plugs in on the passenger side of the block near the oil sending unit.

It is a known issue.

The driver side power seat in my 2017 Jeep Grand Cherokee

JustAnswer https://www.justanswer.com > Jeep Questions Nov 28, 2023 - Every other part of the power seat works (lumbar, vertical adjustment etc) but for some reason it is not moving forward or backwards. I checked ... 1 answer · Top answer: Welcome to JustAnswer. Sorry to hear you have a frustrating experience. I'm glad to assist ... Missing: Overland. ‎' Show results with: Overland.

Driver seat is stuck rearward

Jeep Garage https://www.jeepgarage.org > threads > driver-seat-is-st... Aug 19, 2012 - I have 2004 Overland that automatically moves forward and rearward when unlocking and locking the vehicle. The seat is stuck all the way ... Easy exit seat not working Feb 18, 2018 Driver seat won't move forward Apr 4, 2016 Seat Memory, Easy Entry/Exit not working Aug 3, 2018 Memory Seat not working Feb 23, 2010 More results from www.jeepgarage.org

FIX: front seat stuck forward or seatback won't return to ...

JLwranglerforums.com https://www.jlwranglerforums.com > forum > threads Jan 8, 2022 - It's a known issue. There is one for each seat and it moves along the door-side track. The left and right sides specific and not switchable.

old fords have them and yours does tomine not. ,not my JK Nor wk. I have your real factory service manual here on screen 2. yes, replacing the alternator with the battery connected does blow a fuse. in 1 nano second fast. BOOM , let the smoke out. but saved by the link. OKAY you were right the liberty has that link you were right, it has links ! this is your actual car, wiringi have it all there. FSM PDF real.

So it really is only a jeep XJ body ,not a real jeepsure loved by all sure.jeep has 2003 avalanche LS5.3 ENGINE AND 4L60E TRANS WITH A 6" Lift (ouch) on 37" tires with 1979 Ford 3/4 ton rear ends.with NP231 transfer, np207 gone now with new NP231 transfer case from the '91 YJ ?, NO, from a CHEVYI bet now it is NP231C box, the C means Chevy box.with 2H, 4H, N, and 4L,, this is part time 4wd, not full and is not for the 4wheeling on pavement. only offroad or on ICE.ICE means, just that or snow or snow over ice. (sorry captain Obvious, just left the building,now)end ICE answersbegin, 6" lift extreme problemsthe real problem is the LIFT that high.3 "easy4 hard6 "extreme lifts.IT fails in 2wd mode too, that is because U-Joints have limits. (all do) and the lift span chart below.(angle) post.nothing else needs to known, but U-JOINT ANGLES are all WRONG.SOLVED,. the 6" lift done wrong. YJ is a very short Wrangler and very short rear prop shaft.that means Prop(rear) drive shaft angles are dead wrong. (solved the reason on 1 fact)DOne with no SYE kit. "slip Yoke Eliminator"'https://www.amazon.com/Heavy-Eliminator-52231-18676-60-Driveshaft/dp/B00FDWL7PMdone i bet with no shims for rear axle LEAF spring perches , to get angle right(they sell shim kits)the answer You need a double cardan or CV (same piece different name) at the TC case, this will require a new yolk. You will also need to shim the pinion angle to get the driveshaft and pinion within 2 degrees of each other.

First you will need to determine if there is a problem with the electrical system or fuel system. Connect a fuel pressure gauge to the fuel rail to see if you have pressure when the vehicle dies. It it maintains pressure and the vehicle dies, then check to see if there is a spark issue. Fuel issue could be bad/weak fuel pump, bad relay or restriction in fuel delivery system. No spark could be ignition coil, bad computer, bad electrical connection or relay. To check these systems you need special meters and scanners. Best to take to a repair center.

The most likely reason is a faulty switch or a faulty relay or problem with the Body Control Module computer. https://www.google.com/search?q=auto+electrician+near+me ..

Head bolts